Goodman 1.5 Ton 14.3 SEER2 92% AFUE 80,000 BTU Gas Electric Air Conditioner Split System Horizontal R-32 | GLXS4BA1810 GR9S920803BN CHPTA1822B3

Overview

This matched Goodman split-system package combines one GLXS4BA1810 outdoor air conditioner with one GR9S920803BN gas furnace and one CHPTA1822B3 evaporator coil. It is a nominal 1.5 ton ducted cooling system paired with ducted gas heat for a single air distribution path. The outdoor condenser provides refrigerant compression and heat rejection, while the indoor coil provides the evaporator heat transfer surface within the duct system. The furnace supplies combustion heat and establishes airflow across the coil using its ECM blower for cooling, heating, and circulation modes. The coil is a cased horizontal a-coil (evaporator coil) built for horizontal installation and includes a factory TXV for controlled refrigerant metering. Together, these components operate as one integrated ducted cooling-and-gas-heat system using standard 24V thermostat control with non-communicating equipment logic.

Performance

Cooling capacity control is handled at the outdoor section, while indoor comfort depends on correct airflow setup, coil selection, and refrigerant charge. The TXV coil stabilizes metering under changing indoor load to support consistent evaporator superheat and latent performance. The furnace operates as a single-stage platform to manage heat delivery relative to load, reducing overshoot when staged operation is available. In heating mode, furnace input ranges from 80,000 to 80,000 BTU/h depending on firing stage and demand. Indoor airflow is configured at the furnace to support duct static pressure constraints while maintaining coil temperature targets. Overall system performance is achieved by coordinating refrigerant-side heat transfer at the coil with air-side delivery through the duct network.

Smart Features

Controls follow conventional 24V heat and cool call logic, supporting non-communicating thermostats and third-party smart thermostats with standard outputs. The furnace control system manages ignition sequencing, safety proving, and blower timing, with diagnostics used for troubleshooting. ECM blower speed selection enables airflow tuning for cooling and heating profiles without changing the outdoor control architecture. When applied with zoning dampers, airflow setup and duct design determine how well the system maintains coil temperature stability and zone balance. Service roles stay clear by separating refrigeration service at the outdoor unit from ignition and airflow service at the furnace section. This architecture supports typical replacement and service workflows for ducted split systems.

Comfort & Noise

Comfort is governed by coil face velocity and duct design, with cabinet widths selected so the furnace and coil align for stable air distribution. Staged furnace operation, when present, uses low fire for moderate demand and transitions to high fire when load increases. The ECM blower supports smoother airflow transitions and can be configured for continuous circulation for improved mixing and filtration through the return path. Cooling humidity performance depends on achieving intended evaporator temperature, which is sensitive to airflow setup and refrigerant charge, with the TXV helping stabilize metering. Noise behavior is strongly influenced by duct static pressure and airflow selection at the furnace rather than the refrigerant circuit alone. Overall comfort is produced by coordinated heat rejection outdoors, heat absorption at the indoor coil, and ducted air delivery through the furnace blower.

Use Case Fit

This package is suited for ducted residential applications and can support light commercial or multi-family use where one outdoor condenser serves one duct system. The furnace supports upflow or horizontal left/right installation, while the coil supports horizontal mounting to match common vertical or horizontal duct layouts. Combustion venting requirements follow the furnace platform, including PVC direct vent for condensing models and Category I venting for non-condensing models. Zoning can be applied with dampers where duct design supports stable airflow and coil temperature control in each zone. The furnace NOx classification for this model is > 40 NG/J NOx, which may support compliance requirements depending on jurisdiction. This configuration fits applications where a defined equipment set is used to deliver central cooling and ducted gas heat through one air path.

Value & Reliability

Reliability is supported by conventional split-system architecture with serviceable indoor and outdoor sections and accessible refrigerant and airflow service points. The furnace integrates safety controls for flame sensing, pressure proving, and limit protection to manage combustion operation over repeated cycles. Coil cabinet insulation and drain features support condensate management when installed with proper trapping and drainage. Airflow tuning is supported by the ECM blower, helping match coil performance to duct static and filtration requirements. Standard electrical interfaces and 24V control wiring simplify replacement and service across common installations. Across the package, the value is predictable commissioning steps focused on airflow setup, charge verification, and combustion safety validation.

Summary Wrap-Up

As a complete ducted split system, this package pairs one GLXS4BA1810 outdoor condenser with a 92% AFUE GR9S920803BN gas furnace and a TXV-metered CHPTA1822B3 evaporator coil. The outdoor condenser performs the refrigeration work, while the indoor coil provides evaporator heat transfer and the furnace supplies airflow and combustion heat. Component roles remain separated for serviceability, with refrigeration diagnostics at the condenser and ignition and airflow diagnostics at the furnace. Commissioning centers on blower airflow configuration, refrigerant charge verification, venting completion where applicable, and confirmation of ignition safety operation. For wholesale and D2C buyers, the value is a defined Goodman equipment set with conventional controls and serviceable subassemblies. Select this configuration when you need ducted central cooling paired with gas heat and clear component roles across the refrigeration and combustion sections.

Key Features

• Split-system architecture: One outdoor condenser and one indoor evaporator coil form a ducted refrigeration circuit for central cooling.
• Gas furnace heat section: GR9S920803BN provides ducted combustion heat with single-stage operation and integrated safeties.
• ECM airflow delivery: ECM blower supports airflow setup for cooling, heating, and continuous circulation through the duct network.
• TXV refrigerant metering: CHPTA1822B3 includes a factory TXV to stabilize evaporator operation under changing indoor load.
• Mounting and orientation flexibility: Furnace supports upflow or horizontal left/right installation and the coil supports horizontal mounting.
• Application fit: Matched sizing supports typical residential duct systems where one outdoor unit serves one distribution path.