Mitsubishi Electric 20,000 BTU 20 SEER2 Dual Zone Wall Mounted Ductless Mini Split Heat Pump System 6+9 R454B Refrigerant | MXZ-2D20NL-MSZ-GX06NL-MSZ-GX09NL

Overview

This Mitsubishi Electric multi-zone ductless heat pump system pairs the MXZ-2D20NL outdoor unit with 1 × 6,000 BTU/h wall-mounted indoor unit + 1 × 9,000 BTU/h wall-mounted indoor unit. The outdoor unit is rated at 18,000 BTU/h cooling at 95°F and 24,000 BTU/h heating at 47°F in non-ducted operation. Efficiency is listed at 20 SEER2, 13 EER2, and 10 HSPF2 (IV) for non-ducted systems. The system uses R454B refrigerant with a factory charge of 4 lb 7 oz in the outdoor unit. It is designed to connect 2 indoor units and up to 2 indoor units with 12,000 to 24,000 BTU/h connected capacity. Wall-mounted indoor units provide zone-by-zone set point control for residential and light commercial spaces.

Performance

A Twin Rotary compressor with inverter-driven operation modulates output to match load and maintain stable room temperatures. Outdoor airflow is rated at 1,324 CFM cooling and 1,451 CFM heating, supporting heat exchange across operating conditions. Defrost is handled by Reverse Cycle to maintain heating performance in cold weather. A Blue Fin coated heat exchanger is specified for outdoor coil protection. The outdoor unit supports up to 164 ft of total piping with up to 82 ft to the farthest indoor unit for flexible layouts. Outdoor sound pressure is listed at 51 dB(A) in cooling and 55 dB(A) in heating.

Smart Features

The wall-mounted indoor unit design includes Dual Barrier Coating, Econo Cool, Smart Dry Mode, and Smart Set, with multiple fan speeds and a back-lit handheld remote. Wi‑Fi enabled indoor control pairs with the Comfort app to adjust set points, fan speeds, modes, and schedules. Multiple control options are listed, including wired and wireless controllers and third-party interfaces. Powerful Mode provides a temporary set point and fan speed boost to pull rooms down or warm them up quickly. Smart Set recalls a preferred temperature setting at the touch of a button to simplify daily operation. Smart Dry Mode improves humidity control while minimizing over-cooling during shoulder seasons.

Comfort & Noise

Each wall-mounted zone can operate at its own fan speed and mode selection for room-by-room comfort tuning. Indoor airflow is listed in multiple steps; typical cooling dry airflow includes MSZ-GX06NL 151/182/256/358/448 CFM; MSZ-GX09NL 151/172/256/353/448 CFM across fan settings. Indoor sound ratings are listed for included heads: 19–43 dB(A) depending on fan speed. The outdoor unit’s listed sound levels of 51–55 dB(A) support placement near occupied areas when local codes and site conditions allow. Econo Cool automatically adjusts airflow based on heat exchanger temperature to maintain comfort while reducing unnecessary over-cooling. Built-in electrostatic enzyme filtration is specified, with an optional microparticle filter available.

Use Case Fit

Two-zone ductless layouts fit add-on rooms, remodels, and targeted conditioning where ductwork is limited or not desired. This configuration supports apartment units, townhomes, and small offices that need independent control in two separate areas. Cooling intake air operating limits are listed at 115°F / 14°F, supporting warm-season comfort cooling in many U.S. regions. Heating intake air limits are listed at 6°F DB / 5°F WB with heating lock-out/restart at -4°F / 5°F, helping define cold-weather suitability. Line length and height difference allowances help route piping through basements, attics, and exterior chases for retrofit-friendly installs. Connected indoor capacity is specified from 12,000 to 24,000 BTU/h, aligning with a range of two-zone load combinations.

Value & Reliability

Outdoor protection features include high-pressure protection and compressor thermal protection for system safeguarding under demanding conditions. Fan motor overheating and voltage protection are listed, along with compressor overcurrent detection for additional reliability controls. Blue Fin anti-corrosion treatment is specified on the outdoor heat exchanger for coil protection and longer life. Electrical requirements are listed as 208/230V, 1-phase, 60Hz with recommended 14 AWG interconnect wiring and a 20A recommended fuse/breaker. The outdoor unit is specified with a Optional base pan heater configuration to support cold-weather operation. Compact chassis sizing helps simplify placement on pads, wall brackets, or stands when site layouts are constrained.

Summary Wrap-Up

Choose this Mitsubishi Electric system when you need two independently controlled zones served by a single outdoor unit with inverter-driven modulation. With R454B refrigerant, long piping allowances, and reverse-cycle defrost, it fits common retrofit and new-construction ductless applications. Wall-mounted indoor units add filtration, flexible fan staging, and app-based control to support daily comfort management. Configured correctly, it balances capacity across zones while maintaining stable temperature control during changing loads. It is a practical option for contractors and homeowners seeking a multi-zone solution for bedrooms, living areas, and small offices. Select the indoor unit combination that best matches room loads to complete the two-zone system.

Key Features

• R454B refrigerant system: Uses R454B refrigerant with a factory charge of 4 lb 7 oz in the outdoor unit.
• Inverter-driven twin rotary compressor: Modulates capacity using a Twin Rotary compressor to hold set points and reduce cycling.
• Two-zone connectivity: Designed to connect 2 indoor units and up to 2 indoor units with 12,000–24,000 BTU/h connected capacity.
• Piping flexibility: Supports up to 164 ft total piping and 82 ft to the farthest indoor unit for layout versatility.
• Reverse-cycle defrost: Uses Reverse Cycle to maintain heating performance during cold-weather operation.
• Wall-mounted indoor control: Indoor heads provide multiple fan speeds, Smart Dry Mode, Smart Set, and Wi‑Fi control using the Comfort app.